Cubox-I 4 with Legacy an Mainline Kernel is not booting by using PARTUUID or...
Hello, i was using my cubox-i 4 pro since two years now. Last time (last week) i have used a armbian legacy debian version from whatever, after my hdd corrupted (i have a backup) i tried to setup the...
View ArticleH3 SPI with DMA using kernel 4.10.0
Using the dev build of Armbian for the OrangePi One, does the SPI driver in the mainline kernel support DMA? According to the mainline status page the work on SPI is done, and DMA has been supported...
View ArticleFailure trying to install opejdk 8 headless
On my banana I get the following error: sudo apt-get install openjdk-8-jre-headless Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not...
View ArticleCh340 (USB/UART) on Armbian
Hi, Have Arduino (microcontroller) clone with CH340 USB/UART (USB serial port). Does armbian support it? regards Peter
View ArticleOrangePi Plus/plus2 kernel 4.10
Hi, Following the guide https://docs.armbian.com/Developer-Guide_Build-Preparation/ I compiled a kernel 4.10 and I get: [*] Only appears one CPU. CPU1, CPU2, CPU3 show...
View ArticleCVE-2017-6074: DCCP double-free vulnerability (local root)
For anyone stumbling accross CVE-2017-6074 and thinking about whether Armbian installations are affected or not: we're most probably not since CONFIG_IP_DCCP is enabled as module only on some kernels:...
View ArticleUSB-touchscreen doesn't work with Cubietruck 3.4.113.
USB-touchscreen doesn't work with Cubietruck 3.4.113. The touchscreen well works with versions 4.9.xxx, but doesn't work with 3.4.xxx. I connected the monitor 1920*1080 and a touchscreen to Cubietruck....
View Articlehow to disable verbose ?
in the documentation is written : How to toogle verbose boot? touch /boot/.force-verbose # enable You need to reboot to conduct changes. rm /boot/.force-verbose # disable but I am returned : rm: cannot...
View ArticleCamera problem: /dev/video0 not present
Hi, I am trying to install and run the dedicated camera on OP Lite with Legacy 3.4.113 as written here: http://www.cnx-software.com/2015/09/26/how-to-use-orange-pi-camera-in-linux-with-motion/...
View ArticleSMALLEST rootfs for Orange Pi Zero to fit in 2MB NOR-FLASH on board
Hello, My project does not allow me to use SD card to boot and run my application. I can use SD card as drive to save my data. Is there any alternative way to do so ? Has anyone built a micro...
View ArticleSPI slave
Hi! I want to write SPI slave custom driver for H3. For this I need to cut off existing SPI Master driver. I did this during configuring Armbian 3.4.112 in image build process. But then I make apt...
View ArticleOne usb keyboard for tty1 and ttyS0.
Good day or night. Help me please. I have armbian. And there are - systemd. I do not know how to set up my usb keyboard to make it work with two displays at once. With tty1 and ttyS0 at the same time....
View ArticlePine64 board water cooling, off the wall
Found an interesting way to keep the Pine64 cool. https://www.youtube.com/watch?v=VFq1EbWOfYo
View ArticleHow to enable pwm in orange pi zero?
I could not found pwm folder in the "/sys/class". so, how to enable pwm in orange pi zero?
View ArticleUSB Devices on 5.25 doesn't work well
Hello I have a little problem with the usb devices, i use usb camera and if u plug the power supply to the OPI Lite board (5.25) it recognize the camera but it doesn't work well (stream with like 8-10...
View ArticleH3/NanoPI Neo stock build failed
Hello, While trying to build full Devian Jessy image for NanoPi Neo at stock x86_64 Ubuntu 16.04 using latest https://github.com/igorpecovnik/libgit , got this: ... [ o.k. ] Compiling default...
View ArticleUpdate to 4.9.12-cubox
Hi there, on my Cubox i4 pro there was an update from 4.9.7-cubox to 4.9.12-cubox. It took quite a while, and there were a couple of messages: dpkg: warning: unable to delete old directory...
View ArticleClik here to view.
Orange Pi Zero - Failed to start Load Kernel Modules.
Orange Pi Zero shows error [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. More details How to fix this error?
View ArticleUART on Orange Pi Zero
I was unable to get UART working on my Orange Pi Zero. Note, that I am not trying to use UART to access the terminal, I need to use the UART port to say connect to an arduino, etc. Here is the...
View Article[Odroid C2] filesystem corrupted after boot from emmc
I created a new image for my Odroid C2 with the most current version of Armbian 5.26. Configuration was pretty much standard, except BOOTSIZE=0 and ROOTFS_TYPE=ext4. The image works fine, if dumped to...
View Article