Hello,
using newest Legacy Image Armbian_5.04_Cubietruck_Debian_jessie_3.4.110 there is still a wifi problem while booting. Correct?
For more than one minute the boot process hangs showing following error message:
"A Start Job is running for LSB: Raise network interfaces"
After one minute the boot process continues. The wlan0 connection gets somehow established. But it is slowly und not really stable.
root@cubietruck:~$ cat /etc/network/interfaces auto eth0 iface eth0 inet dhcp auto wlan0 iface wlan0 inet dhcp wpa-ssid My-SSID wpa-psk My-Password auto lo iface lo inet loopback
root@cubietruck:~$ lsmod Module Size Used by cpufreq_userspace 3524 0 sg 23765 0 ap6210 625672 0 sunxi_ir 4037 0 hidp 17640 0 rfcomm 58686 0 hci_uart 25000 0 bluetooth 264185 5 hidp,hci_uart,rfcomm
dmesg:
[ 5.651519] systemd[1]: Starting Syslog Socket. [ 5.656508] systemd[1]: Listening on Syslog Socket. [ 5.660963] systemd[1]: Starting Journal Service... [ 5.692171] systemd[1]: Started Journal Service. [ 5.702433] input: sunxi-ir as /devices/virtual/input/input4 [ 5.704280] IR Initial OK [ 5.804250] [ap6210] select wifi ap6210 [ 5.815858] [ap6210] Initializing ap6210. [ 5.822280] [ap6210] platform device registered successfully. [ 5.826606] [ap6210] Using ap6210 configuration. [ 5.944254] [mmc-msg] sdc3 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 5.958970] [mmc-msg] sdc3 power on [ 5.984883] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 5.989811] [mmc-msg] sdc3 set round clock 400000, src 24000000 [ 6.070155] [ap6210] WLAN placed in POWER ON [ 6.082203] [mmc-err] smc 3 err, cmd 52, RTO [ 6.086349] [mmc-err] smc 3 err, cmd 52, RTO [ 6.094725] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 6.106362] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 6.114847] [mmc-err] smc 3 err, cmd 8, RTO [ 6.123881] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 6.127901] systemd-udevd[105]: starting version 215 [ 6.147256] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 6.160363] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 6.172289] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 6.179640] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 6.209152] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 6.221414] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 6.226696] [mmc-msg] sdc3 set round clock 42857143, src 600000000 [ 6.290586] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 6.300506] mmc1: new high speed SDIO card at address 0001 [ 6.304969] [ap6210] Linux Kernel SDIO/MMC Driver [ 6.324122] [ap6210] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33 [ 6.816813] [ap6210] WLAN placed in RESET [ 7.217988] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 7.628632] EXT4-fs (mmcblk0p1): re-mounted. Opts: data=writeback,commit=600,errors=remount-ro [ 8.135661] Adding 131068k swap on /var/swap. Priority:-1 extents:1 across:131068k SS [ 8.219590] [ap6210] Using ap6210 configuration. [ 8.682494] systemd-journald[101]: Received request to flush runtime journal from PID 1 [ 9.186599] sunxi_gmac: probed [ 9.192082] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 9.196875] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01) [ 11.199742] PHY: sunxi_gmac-0:00 - Link is Up - 100/Full [ 19.799483] eth0: no IPv6 routers present [ 62.638592] usb 5-1: USB disconnect, device number 2 [ 63.895608] ehci_irq: port change detect [ 63.939154] ehci_irq: port change detect [ 64.281851] usb 5-1: new low-speed USB device number 3 using sw-ohci [ 64.514315] input: Logitech USB Optical Mouse as /devices/platform/sw-ohci.2/usb5/5-1/5-1:1.0/input/input5 [ 64.526236] generic-usb 0003:046D:C05A.0004: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-sw-ohci-1/input0 [ 70.160329] [ap6210] Dongle Host Driver, version 1.28.23.3 (r). [ 70.167432] [ap6210] Compiled in drivers/net/wireless/ap6210 on Feb 28 2016 at 17:13:38. [ 70.371036] [ap6210] WLAN going back to live [ 70.372797] sdio_reset_comm(): [ 70.381236] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.391740] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.401051] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.405984] [mmc-msg] sdc3 set round clock 400000, src 24000000 [ 70.469641] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.483433] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 70.489429] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 70.495419] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 70.502650] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 70.524561] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.533018] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.538189] [mmc-msg] sdc3 set round clock 42857143, src 600000000 [ 70.601725] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.605556] [ap6210] dhd_bus_devreset: WLAN ON [ 70.611595] [ap6210] Final fw_path=/lib/firmware/ap6210/fw_bcm40181a2.bin [ 70.622316] [ap6210] Final nv_path=/lib/firmware/ap6210/nvram_ap6210.txt [ 70.628912] [ap6210] download firmware /lib/firmware/ap6210/fw_bcm40181a2.bin [ 70.919909] [ap6210] Dongle ready, protocol version 4 [ 70.926526] [ap6210] Dongle ready, protocol version 4 [ 70.938148] [ap6210] Firmware up: op_mode=0x0005, Broadcom Dongle Host Driver mac=98:3b:16:81:07:59 [ 70.956258] [ap6210] Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d [ 70.959244] [ap6210] Chip: a962 Rev 1 Pkg 9 [ 70.965738] [ap6210] p2p0: p2p_dev_addr=9a:3b:16:81:07:59 [ 81.139641] wlan0: no IPv6 routers present [ 86.517656] [ap6210] Couldn't find P2PIE in probe response/beacon [ 86.528817] [ap6210] Couldn't find P2PIE in probe response/beacon [ 86.538836] [ap6210] Couldn't find P2PIE in probe response/beacon [ 86.544727] [ap6210] Couldn't find P2PIE in probe response/beacon [ 86.604441] [ap6210] Couldn't find P2PIE in probe response/beacon [ 92.110103] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b03 on p2p0 I/F. Ignoring. [ 92.117048] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b1d on p2p0 I/F. Ignoring. [ 92.124434] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b09 on p2p0 I/F. Ignoring. [ 93.691415] sunxi_gmac: probed [ 93.696989] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 93.701965] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01) [ 93.718579] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 94.249248] sunxi_gmac: probed [ 94.254660] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 94.259513] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01) [ 94.279591] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 96.259989] PHY: sunxi_gmac-0:00 - Link is Up - 100/Full [ 96.267265] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 103.009724] p2p0: no IPv6 routers present [ 106.819706] eth0: no IPv6 routers present [ 159.413080] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.418491] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.433247] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.438638] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.444145] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.449463] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.792900] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.798485] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.810808] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.816694] [ap6210] Couldn't find P2PIE in probe response/beacon [ 161.108750] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b03 on p2p0 I/F. Ignoring. [ 161.115986] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b1d on p2p0 I/F. Ignoring. [ 161.123417] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b09 on p2p0 I/F. Ignoring. [ 162.865714] sunxi_gmac: probed [ 162.871125] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 162.876087] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01) [ 162.892353] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 164.870859] PHY: sunxi_gmac-0:00 - Link is Up - 100/Full [ 164.878790] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 172.870632] p2p0: no IPv6 routers present
Thanks in advance!